To take the performance of Netgear WiFi range extender, users update its firmware. But, 99 percent of users report that whenever they try to update Netgear extender’s firmware after connecting to Netgear_ext they get won’t get success, but get stuck with the process. If you are also one of them, then following the fixes provided here can prove helpful to you in a bigger way. So, stop thinking much to apply the fixes. We assure you that this will be your last search on Google for the issue.
Resolved: Extender Firmware Update Stuck
Fix 1: Start troubleshooting the issue by checking the extender’s power supply. Yes, that’s correct! Look, if you extender is not getting a steady power supply, chances are the firmware update process may stuck or interrupt in between. So, a continuous power to the extender is very much important. And, if you are updating extender’s firmware on inverter, we strictly advise, skip this step.
Fix 2: Are you sure that you are connected to Netgear_ext? It seems not! Verify the same. And, if you have customized the default SSID of your Netgear extender, just connect to that one. Not only this, you have to use the correct password to connect to the extender’s SSID.
Still No Luck?
Oh! It seems like the things are still not in your hand, are they? But, why are you worrying? We are here and the article is still left. What we suggest, access Netgear Genie smart setup page using 192.168.1.250. Just ensure that you have followed the exact Netgear extender firmware update instructions. In case you have a doubt, then apply the firmware update process again. What’s the big deal? There is nothing to worry about. But, do provide your extender’s model number. The reason is, firmware updates vary upon extender model to model. So, provide the model number of the extender (if asked) prior to updating the latest version of firmware on it.
Fix 4: Another effective fix that you can apply is to check the connection between your Netgear device and router. We hope that you have already made it? No? Well, you now have the biggest reasons behind getting firmware update stuck issue. Users, connection between your extender and router is very important to complete the firmware update process. But, a stable connection, not loose or unsecured, got it?
Fix 5: Have you configured your Netgear extender properly. Yes, this is one of the most crucial steps before updating extender’s firmware. Yes, only after configuring the Netgear extender using mywifiext setup instructions you get notification to update firmware. And, if your extender is not configured properly, you won’t get any updates. Still, if you get updates anyway, you will get to see firmware update stuck error message continuously.
Getting Stuck with the Same Error?
If nothing helped you to fix the Netgear extender firmware update stuck error message, then you can try resetting your device i.e. the extender back to factory default settings. Yes, this is one of the most effective fixes to troubleshoot the issue. So, to reset the extender, all you have to do is to:
Get disconnected from Netgear_ext and also disconnect extender from router.
Locate the extender’s reset hole and hold it up for a couple of seconds using a pin, toothpick, paper clip, etc. and release it slowly.
Wait for the extender’s power LED to start blinking green.
After resetting the device, perform the Netgear WiFi extender setup instructions from the scratch using mywifiext setup instructions. This time, ensure to configure the extender in a proper way. And, once the Netgear WiFi extender setup process gets completed, you will have the new extended SSID, don’t you? If you got the SSID, get connected to it and try to update the Netgear extender’s firmware again. This time, we are 100% sure that you will not receive the Netgear extender firmware update stuck message again.
Just remember a couple of points outlined below:
Do not interrupt the process
Stay within reach of your extender’s WiFi till the firmware update process is going on
Have patience the firmware update process will surely take much time
The extender will reboot automatically so don’t get worried. This indicates a good sign that the firmware is successfully updated.
The Last Words
Getting Netgear extender firmware update stuck error message has become very common these days. But, this is the case that is not with you anymore because you have applied the fixes provided here. We hope that you find them helpful? If you prefer, please share your valuable feedback with us.
.jpg)
